Franklin Performance

New clutch slave cylinder push rod to suit all RB20 turbo and non-turbo gearboxes. Often a hard part to source when performing a manual conversion ...

Braided clutch line to suit Nissan RB20 style gearboxes in Nissan R32 R33 R34 S13 S14 S15 A31 C33 C34 C35 vehicles. The braided clutch line is desi...

Braided clutch line to suit Nissan RB25 Turbo (Big) gearboxes in Nissan R32 R33 R34 S13 S14 S15 A31 C33 C34 C35 vehicles. The braided clutch line i...

Franklin Performance is proud to produce solid steering column bushes for a range of Nissan vehicles. This aluminium bush replaces the soft rubber ...

High quality 10AN stainless steel double braided fuel/oil line to suit reusable hose ends  Dimensions: 14.3mm ID & 19.85mm OD Pressure Rating: ...

These spacers are installed on the steering rack, spacing the rack end further out and allow the steering rack shaft to travel further inside the s...

High quality braided turbo oil drain kit specifically for Nissan RB / SR / CA engines. The kit contains: 500mm 10AN Braided Hose 10AN Straight Hose...

High quality turbo oil feed kit to suit Nissan RB / SR / CA engines with aftermarket turbos. Kit contains: Turbo flange adaptor with 40mm bolt hole...

Coil conversion kit??manufactured by Franklin Performance to fit modern high power Nissan VR38 coils to Nissan RB20, RB25 and RB26 engines, includi...

Brand new 6-pin loom plug to suit Nissan R32 RB coil ignitors, and R33 S1 ignitors. On R32 engines this is the 6-pin plug that is on the engine loo...

Push-in 10AN rocker cover fittings for Nissan RB26DETT engines. CNC Machined from billet 6061-T6 aluminium and black anodised for great looks and l...

Aluminium bush to fit 17mm bore aftermarket pulleys??to 15mm shaft size alternators. 15mm inside diameter 17mm outside diameter 5.5mm long CNC ma...

Anodised aluminium??hose barb fitting available in the following sizes: 6AN to 5/16" (8mm) Hose Barb 10AN to 5/8" (16mm) Hose Barb High quality ...

100 series AN 45 degree hose ends, allowing??you to connect 100 series braided hose to AN male fittings. ??

Billet aluminium oil restrictor designed to fit in the end of a male 3AN or 4AN fitting to restrict oil flow to a turbo or similar application. Ava...

Drills and tap required to install one of our Nissan RB30DET VCT Oil Feed Kits. Contains: 8.3mm Drill 1/16" NPT Tap 1/8" NPT Tap

Oil orifice restrictors for Nissan RB engines. When building an RB20, RB25, RB26 or RB30 engine it is common practice to restrict the amount of oil...

Aluminium double belt alternator pulley to suit early 12A and 13B rotaries through to series 5 RX-7 (vehicles with 15 mm alternator shaft). It allo...

High quality turbo oil feed kit to suit Nissan RB / SR / CA engines with standard turbos, either high-mount or low-mount. The kit contains: USA Ma...

Setrab 18 row 145 x 285 x 50mm cooler with M18x1.5 threaded ports.?? Setrab are a Swedish company who make some of the highest quality oil coolers ...

Brand new 3-pin loom plug to suit Toyota 1JZ-GTE and 2JZ-GTE 4 pin TPS units. ?? Please check your original connector???s shape and keying before p...

A steel lambda / oxygen / wideband boss for welding into your exhaust system. - M18x1.5 thread compatible with most aftermarket and factory oxygen ...

A steel lambda / oxygen / O2 / wideband boss for welding into your exhaust system, complete with blaking plug and copper washer. - M18x1.5 thread c...

Designed to lock the subframe in place by compressing the factory bushes, they will reduce the wheelspin and firm up the rear suspension by elimina...