Franklin Performance

VCT oil return kit for Nissan RB25DET & RB25DE engines. The VCT oil drain sits just in front of the exhaust manifold and helps to drain excess ...

Replacement door lock knob set for Mazda 1000 1200 R100 RX2 RX3 RX4 vehicles, available in three different designs: Round, Aluminium Round, Blac...

Oil filter stud manufactured by Franklin Engineering for fitting an oil filter directly to a Nissan RB engine, slowing you to remove the oil filter...

Short coil stalk for Nissan VR38 coils to allow a more compact installation of the VR38 coil in an aftermarket application. The shortened coil stal...

Push-in blanking plug to replace the PCV valve on many models of Nissan engines. Application: S14 Silvia 200sx S15 Silvia 200sx T30 X-Trail (SR20v...

Coil conversion kit manufactured by Franklin Performance to fit modern high power Nissan VR38 coils to Toyota 1JZGTE & 2JZGTE engines. Our kits...

SplitFire Coil Pack for Nissan GTR R35 - VR38DETT. The SplitFire Super Direct Ignition System was developed to improve power of ignition system ado...

Keep your shoulder belts or head containment net straps in place with our billet aluminium two piece piece belt guide clamps that fit 1.5" roll bar...

Billet alternator bracket manufactured by Franklin Engineering for a range of Nissan RB powered vehicles. CNC machined from billet 6061-T6 aluminiu...

10AN heater hose adaptor fitting for the rear of the thermostat housing on Nissan RB Engines. Compatibility: Nissan RB20DE, RB20DET Nissan RB25DE,...

6AN anodised aluminium banjo fitting. M14 (14.5mm hole size) M16 (16.5mm hole size) M18 (18.5mm hole size) Banjo bolts and copper washers are a...

Black anodised aluminium banjo bolt  M14x1.5 M16x1.5 M18x1.5 Banjo fittings and copper washers are also available.  

Aluminium soft jaw set used for assembling anodised hose ends & fittings. Length: 100mm Colour: Black Sold as a pair.

We have lots of surplus bar ends and offcuts of 6061 aluminium solid round bar. Sizes from 12.7mm (1/2") to 57mm (2.25") round - lengths vary from ...

The GS100502 is a Gear Tooth Speed Sensor, hall-effect device designed for use in applications where ferrous edge detection/near zero speed sensing...

High quality 35mm2 single core black flexible cable. Sold per metre. Add the amount you require to your shopping cart and we'll cut to length for y...

Aluminium plug designed to fit into dipstick hole in a Mazda 12A / 13B / 20B rotary centre plate. Often required for dry-sump, 20B or quad rotor ap...

10AN rocker cover fitting for Mitsubishi Lancer Evolution X engines. It is threaded to screw straight into the factory rocker cover PCV valve port,...

This billet aluminium thermostat housing replacement has been designed by Franklin Performance to replace the factory housing on all Nissan RB engi...

Brand new short style master cylinder found factory in S14 and R33. These units are often used where clearance of larger intake manifolds is requir...

Solid exhaust side engine mount for 4WD Nissan RB engines. This a direct replacement of the standard item to help reduce engine movement and get po...

Coil conversion kit manufactured by Franklin Performance to fit modern high power Nissan VR38 coils to Mazda Series 6 & Series 5 13B engines. T...

Weld-on boss for fitting 1/4" diameter EGT sensors to an exhaust manifold. 1/8" NPT 7/16"-20 thread CNC machined from 304 stainless steel at our ...

Plastic oil cap to suit our billet aluminium filler necks, weld on bosses and factory Mazda Rotary engines, other than RX8 after March 2008.